K416B Ni-based superalloy with high W content has good high temperature properties and low cost,which has a great development potential.To investigate the room temperature tensile property and the deformation feature of K416B superalloy,tensile testing at room temperature was carried out,and optical microscopy (OM),scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to analyze the deformation and damage mechanisms.Results show that the main room temperature tensile deformation features of the K416B nickel-based superalloy are dislocations slipping in the matrix and shearing into γ’ phase.The <110> super-dislocations shearing into γ’ phase can form the anti-phase boundary two coupled (a/2)<110> partial-dislocations or decompose into the configuration of two (a/3)<112> partial dislocations plus stacking fault.In the later stage of tensile testing,the slip-lines with different orientations are activated in the grain,causing the stress concentration in the regions of block carbide or the porosity,and cracks initiate and propagate along these regions.
The properties of Ni-base superalloy castings microstructure, and different solidification methods have are closely related to the uniformity of their as-cast serious effect on microstructural uniformity. In this paper, the influences of high rate solidification （HRS） process （with or without superheating） and liquid metal cooling （LMC） process on the microstructure of DZ125 superalloy were investigated. Blade-shape castings were solidified at rates of 40 pm.s-1 to 110 tJm.s1 using HRS process and a comparative experiment was carried out at a rate of 70 IJm.s1 by LMC process. The optical microscope （OM）, scanning electron microscope （SEM） were used to observe the microstructure and the grain size was analyzed using electron back scattered diffraction （EBSD） technique. Results show that for the castings by either HRS or LMC process, the primary dendrite arm spacing and size of 7＇ precipitates decrease with increasing the withdrawal rate; the dendrites and 7＇ precipitates at the upper section of the blade are coarser than those in the middle, especially for the HRS castings without high superheating technique. When the withdrawal rate is 70 iJm.s1, the castings by HRS with high superheating technique have the smallest PDAS with fine 7＇ precipitates; while the size distribution of 7＇ precipitates is more homogenous in LMC castings, and the number of larger grains in LMC castings is smaller than that in the HRS castings. Moreover, high superheating technique yields smaller grains in the castings. Both the LMC method and HRS with high superheating technique can be used to prepare castings with reduced maximum grain size.
Ge BingmingLiu LinZhang JunLi YafengFu HengzhiLiu Xiaofu
The pattern of dendritic growth and distortion of dendritic network in the platform have been investigated by one mold casting with different platform length during directional solidification. As the platform length elongates, the symmetry of dendritic growth along left and right edges gradually worsens in platform base. While the platform length reaches 14 mm, the distortion of dendritic network is first observed in outward platform. It is found that the distortion of dendritic network along platform inside is more serious than that along platform edges. Both [001] deviation and accumulated misorientation along platform inside, up to 9~ and 16.3~, respectively, are far greeter than those along left-outward-right edges. The deformation of dendritic network in a platform may be caused by the asymmetry of the solidification front at the mush zone.
Xiaoli ZhangYizhou ZhouYanyun HanTao JinXiaofeng Sun
The recrystallization behavior of a single crystal nickel-base superalloy was investigated by shot peening and subsequent annealing. Two kinds of recrystallization microstructures, which are intensively dependent on the annealing temperature, are shown in the nickel-base superalloy after shot peening and subsequent annealing. Surface recrystallized grains are obtained when the superalloy is annealed at solution treatment temperature. The nucleation of recrystallization originates from the dendritic core, where rapid dissolution of γ＇ particles occurs. Cellular recrystallization is observed after annealing at lower temperatures. Cellular structures induced by high diffusivity of the moving boundary and more γ＇ particles dissolution led by residual stress are developed from the surface region. Recrystallized kinetics of the shot-peened alloy annealed at 1050°C accords with the Johnson-Mehl-Avrami-Kolmogorov equation. The low Avrami exponent is caused by the inhomogeneous distribution of stored energy, the decreasing of stored energy during recovery, and the strong resistance of boundary migration by γ＇ particles.
